Powerhorse Gas Cold Water Pressure Washer — 2.5 GPM, 3000 PSI, Electric Start, Model# 1577249

Yes. The power of this machine will strip old paint. Depending on it's condition it may take some time.

yes but be careful it will also feather the wood if you get too close, use caution.

It will remove only what is trying to release. If the water pressure can get under a corner of the paint and under it it might take up more paint I think you might find out that the face of the wood would release first along with the paint.

Yes, this Powerhorse pressure washer will work great for removing paint from a deck, you may want to purchase additional nozzles to assist in better performance. Please see the nozzles listed below...

It says in the manual to drain all the water and fill with anitfreeze during winter months... sounds like a good plan.

The amount of water in the pump itself, when not in use is negligible. Just tipping the unit would drain most of the water out. An 8" piece of old garden hose with a male connection could be used to pour any automotive anti-freeze into the pump. Anti-freeze won't hurt the casting and will keep the seals lubricated. I honestly believe that the pump could be drained 100% just by tipping it back.

there are instructions in the owners manual on how to put automotive antifreeze in the pump for winter storage. it's very simple to do. you can read the pdf file owners manual on the page advertising this washer.

Yes, the procedure that is outlined in the owners manual available in .pdf format on the bottom of the product page, is as follows.

Winter Storage
Protect your pump, hose, and gun from freezing.
Items needed: 12” piece of garden hose or equivalent, funnel and RV antifreeze (approximately
6 oz.)
1.) Follow the storage instructions listed.
2.) Disconnect spark plug cable. Make sure the engine start switch is OFF, and the fuel valve is
OFF.
3.) Attach the garden hose with funnel to the pump inlet (see illustration).
4.) Pour RV antifreeze into the funnel, pull the engine recoil until antifreeze comes out the pump
outlet.
5.) Drain all water from the high pressure hose. Depress trigger on gun and drain all water out of
gun/lance.

There are 2 of them. If you called the recoil rope as the face, one is on the right rear. The other is at the left rear. Both are about 3" up from the base, but the left side fill is partially under the cylinder cooling fins and is more difficult to access. The right side is easy access. Both are black threaded twist caps with "O" ring seals. There are also 2 separate drains on the left and right side base plate.

In the picture shown for this Powerhorse pressure washer the oil refill cap is located to the right and above the right tire on the engine crank case, the cap is black in color.

It is on the side of the engine towards the bottom. It has a black cap.

To verify your question, are you asking about the oil fill for the engine or for the pump? Each needs to be checked and filled separately as there are different fill points for each.
For the pump there are actually three different fill points. The two lower fill caps have a dipstick built into the caps with which you can confirm the fill level. those two fill caps are down low on the pump casing that is silver colored (the caps are black plastic). One cap is located on each side of the pump near its base.
There is one engine oil fill cap that is also black plastic. It is located on the top of the engine.
The engine has oil in it from the factory. The pump does not.
You may want to do an online search for both the pump and the engine. Manuals for both are online. Hope that this wasn't more info than you needed.

i did not when i moved furniture I just put the spray wand down. the cheaper models cool the pump via water, the pump is oil cooled. I would not run it for 30 minutes or longer without using the wand if that were the case i would shut the unit off, but for a few minutes at a time it is not a problem

To ensure pump life we recommended that any pressure washer not be left running for periods of over 1.5 minutes without either depressing the trigger on the spray gun or shutting down the machine.

Make sure you check out the customer reviews of this product located on the product page just below the "add to cart" icon. The quality that this unit provides at an economy price has made it one of our most popular units.

Not recomended to leave on with wand not engaged on any pressure washer

most all pressure washer pumps have a high temp blow off valve on them but should still not be run for long periods of time without pulling the trigger to circlulate new cold water trought them. Not sure about the idel down..

There is no tank for chemicals/cleaners/detergents. BUT...
There is a pipe nipple downstream of the pump that accepts a flexible hose (which is included with the pressure washer). On the end of this flexible hose is a small filtration unit. To use the pressure washer with chemicals, attach the hose to the pipe nipple and place other end of the hose - the one with the filtration unit - into a jar/bottle/cup containing the chemical you wish to use. Pressure through the system will "siphon" the chemical out and mix it with the water already going through, so by the time the solution sprays out of the nozzle on the tip of the wand, the water and chemical are already mixed and spraying on whatever you are cleaning.

The unit comes with a siphon hose that you insert into a bottle of cleaning liquid.

You change the nozzle on the wand to the black low pressure dispensing nozzel.

Spray the item with the 'soap'

Change the nozzle on the wand to the pressure nozzle and wash away.

There is a suction hose with strainer for washing with chemical cleaner. There is a hose hook that can hold a tank or you can simply place the tank on the ground near the washer and place the suction hose into the tank.

There is a separate host that attaches to the top of the water outlet that you can use with detergent. only use this with the detergent nozle.

yes, there is an adjustment that holds your setting in place

To obtain the lowest pressure you have to set the engine throttle at the lowest setting and turn the pressure all the way down on the adjusting knob. There's not going to be a whole lot of pressure at this setting. Good for cleaning tarps, and items that theres a concern of blasting through it.

The pressure can be adjusted to almost nothing through the use of the unloader valve on the pump. For applications where the pressure is critical, the use of an inline pressure gauge can be helpful. See link below for more details.

Be sure to check out the customer reviews on this product located below the " add to cart" link on the product page. The high quality of our Powerhorse products at an affordable price has made them extremely popular with our customers.

Engine oil affects performance and service life. Use 4-stroke automotive detergent oil. SAE 10W-30 is recommended for general use.

10W-30 is recommended. SAE 30 is also ok, as long as the operating ambient temperature is above 45 degrees F.

10W30 as recommended in the owners manual.

Your volume of water is more critical than your water pressure. You need to be able to fill a 5 gallon bucket in about 90 seconds with the hose you will be feeding your power washer with. I ran a dedicated 3/4" line and sillcock in my garage in order to supply this machine. Seems to word great.

This Powerhorse Gas-Powered Pressure Washer does require positive pressure. As long as you can fill a 5 gallon in 100 seconds your well will provide enough water for this pressure washer. Accurate time keeping is essential.

Hold the trigger open while you start the machine. It starts so easily, this won't be problem. If the pressure is not released it is harder to start. You don't need a compression release for the engine, just release the pressure in the pump.

No, This Powerhorse pressure washer is not equipped with a compression release for easier pull starting.

no the black nozzle has to be attached to draw chemical so you can leave it hooked up just use a different nozzle

For this Powerhorse pressure washer the detergent injector only operates when you are using the detergent nozzle, so you simply use a different nozzle and leave the hose alone when not applying chemicals.